![cisco smart serial crossover cable for 1941 router cisco smart serial crossover cable for 1941 router](https://www.certificationtrainingsolutions.com/wp-content/uploads/2020/01/rsultimate.jpg)
- #Cisco smart serial crossover cable for 1941 router 64 bits
- #Cisco smart serial crossover cable for 1941 router software
- #Cisco smart serial crossover cable for 1941 router license
Interface IP-Address OK? Method Status ProtocolĮmbedded-Service-Engine0/0 unassigned YES unset administratively down down
![cisco smart serial crossover cable for 1941 router cisco smart serial crossover cable for 1941 router](https://www.picclickimg.com/d/l400/pict/202236192819_/Original-Cisco-CAB-X21MT-Router-Serial-DTE-DCE.jpg)
Router#copy startup-config running-configĢ958 bytes copied in 0.224 secs (13205 bytes/sec)Įnter configuration commands, one per line.
![cisco smart serial crossover cable for 1941 router cisco smart serial crossover cable for 1941 router](https://p.globalsources.com/IMAGES/PDT/SMALL/060/S1138601060.jpg)
Nov 20 12:58:12.811: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing Nov 20 12:58:12.711: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthe Nov 20 12:58:12.711: %LINEPROTO-5-UPDOWN: Line protocol on Interface Embedded-Se Nov 20 12:58:11.399: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed stat Nov 20 12:58:11.399: %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed stat Is ignored based on the configuration register setting. Nov 20 12:58:06.479: %SYS-6-STARTUP_CONFIG_IGNORED: System startup configuration
![cisco smart serial crossover cable for 1941 router cisco smart serial crossover cable for 1941 router](https://i.ytimg.com/vi/dRA43DaPX5E/hqdefault.jpg)
Nov 20 12:58:05.679: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthe Nov 20 12:58:04.499: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state Nov 20 12:58:04.495: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state
#Cisco smart serial crossover cable for 1941 router license
= c1900 Next reboot level = ipbasek9 and License = ipbasek9 Jan 2 12:00:02.359: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name Would you like to enter the initial configuration dialog? : n
#Cisco smart serial crossover cable for 1941 router 64 bits
Ĭisco CISCO1941/K9 (revision 1.0) with 487424K/36864K bytes of memory.ĭRAM configuration is 64 bits wide with parity disabled.Ģ55K bytes of non-volatile configuration memory.Ģ50880K bytes of ATA System CompactFlash 0 (Read/Write) If you require further assistance please contact us by sending email. laws governing Cisco cryptographic products may be found at: and local laws, return this product immediately.Ī summary of U.S. By using this product youĪgree to comply with applicable laws and regulations. Importers, exporters, distributors and users are responsible forĬompliance with U.S. Third-party authority to import, export, distribute or use encryption. Delivery of Cisco cryptographic products does not imply States and local country laws governing import, export, transfer and This product contains cryptographic features and is subject to United (c) (1) (ii) of the Rights in Technical Data and Computer
#Cisco smart serial crossover cable for 1941 router software
(c) of the Commercial Computer Software - Restricted Subject to restrictions as set forth in subparagraph Use, duplication, or disclosure by the Government is You must reset or power cycle for new config to take effect Monitor: command "boot" aborted due to user interrupt Program load complete, entry point: 0x80803000, size: 0x1b340 Main memory is configured to 64/-1(On-board/DIMM0) bit mode with ECC disabled Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MBĬISCO1941/K9 platform with 524288 Kbytes of main memory System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)Ĭopyright (c) 2011 by cisco Systems, Inc. I do not have the log in name and need to reset the credentials soon) (here is the data that i pulled from rebooting the router. I have been searching for days on where/what to start with. When i remove the T1 lines, and insert the cable line, the modem and router will not communicate. I know that the multilink on the router is set to TFTP (if this makes a difference). I know ultimately the router will have to be configured to DHCP as per the ISP's instructions. Now what I am wanting to do, is switch to one cable line, and later add in a second one. I have an ethernet cable coming from the IE0/0 port going to a small 6 port switch which my servers are ran off of. I am new to Cisco routers, and trying to figure out what is needed to complete my router setup.Ĭurrently, I have a Cisco 1941 router, with a VWIC3-2MFT-T1/E1 card installed in EHWIC 0 slot.